Denon DN-X1500S Instrukcja Użytkownika Pobierz pdf (Strona 7)

ENGLISH

(2) Rear panel

$0 LINE2, 4, 6, 7, 8 input jacks

• These stereo pairs of unbalanced RCA jacks are

inputs for any line level device.

$1 PHONO1, 2, 3 / LINE1, 3, 5 input

jacks

• These stereo pairs of unbalanced RCA jacks are

inputs for a PHONO (RIAA) stage for magnetic

(MM) cartridges or a LINE stage suitable for any

device, such as a CD player.

$2 PHONO1, 2, 3 / LINE1, 3, 5 switches

• These switches change the input from PHONO

to a LINE level inputs.

• These switches set a LINE level inputs when

turntable is not connected.

$3 Phono ground screw (GND)

• This screws provide a place to connect the

ground wire from a turntable.

This terminal is exclusively for a turntable

grounding and not a safety earth ground.

$4 AUX MIC input jack

• Accepts a balanced microphone with 1/4” TRS

mono jacks.

• Pin layout: Tip=Hot Ring=Cold Sleeve=GND

$5 MAIN MIC input connector

• Neutrik combo jack.

• Accepts either a balanced microphone with an

XLR connector or an unbalanced microphone

with 1/4” TS mono jacks.

• Pin layout:

XLR: 1. GND 2. Hot 3. Cold

$6 Maintenance connector

NOTE:

This connector can be used only for firmware

updating. Do not connect device, or may cause

damage.

$7 LINE2, 4, 6, 8 FADER output jacks

• Connect these jacks to the FADER input jacks of

DN-S3500, DN-S5000, DN-D4500 and etc. using

the 3.5 mm stereo mini cord.

$8 SEND / RETURN jacks

• These 1/4” TS mono jacks allow external

processing of the program signal.

• When connect monaural type effect processor,

use Lch input and output.

$9 DIGITAL OUT (COAXIAL) jack

• This RCA jack provides a digital output data. The

signal is unaffected by the MASTER LEVEL

control.

•We recommend using a 75 Ω/ohm RCA cord for

best digital transfer. (available from any

audio/video retailer)

%0 REC OUT jacks

• This stereo pair of RCA jacks provide a line level

output. The signal is unaffected by the MASTER

LEVEL control.

%1 BOOTH OUT jacks

• This stereo pair of RCA jacks provide a

unbalanced line level output with independent

top panel BOOTH LEVEL control.

%2 MASTER OUT (UNBALANCED)

jacks

• This stereo pair of RCA jacks provide a

unbalanced line level output.

• Connect these jacks to the unbalanced analog

input jacks on an amplifier or console.

%3 LEVEL ATT

(Master out level attenuator)

• Use this to attenuate the MASTER output level.

(–

∞

~ 0 dB)

• Reference is 0 dB.

%4 MASTER OUT (BALANCED)

connectors

• These XLR type connectors provide a balanced

line level output.

• Connect these connectors to the balanced

analog input connectors on an amplifier or

console.

• Pin layout: 1. GND 2. Hot 3. Cold

• Applicable connector:

Cannon XLR-3-31 or equivalent.

NOTE:

Do not short-circuit the hot or cold pin with the

GND pin.

%5 MASTER MONO OUT ON/OFF

switch

• When this switch is on, mixed L and R signal is

outputted from the MASTER OUT (Both

BALANCED and UNBALANCED).

(3) Display

%6 Crossfader A assign indicators

• This indicator shows channels of assigned

channel to Crossfader A side.

%7 Preset mode indicators

%8 Sampler mode indicators

SAMP.:

• The Sampler sound is recorded.

LOOP:

• Playing Sampler in Loop mode.

REV.:

• Reverse Sampler playback.

%9 Character display

• This displays various operational information,

etc..

• [ 1 ] : CH-1 indicator

[ 2 ] : CH-2 indicator

[ 3 ] : CH-3 indicator

[ 4 ] : CH-4 indicator

The number of assigned input source is

displayed on the character display under these

indicator.

^0 Effect assign indicators

• Selected Effector source is indicated here.

^1 Crossfader B assign indicators

• This indicator shows channels of assigned

channel to Crossfader B side.

^2 Effector BPM display

• This display indicates the BPM of the assigned

source.

^3 BPM mode indicators

AUTO:

• This indicator is lit, when the BPM mode is

AUTO BPM.

• This indicator is flashed, when the AUTO BPM

is locked.

MANUAL:

• This indicator is lit, when the BPM mode is

manual BPM input. You can input desired BPM

by MODE PARAMETER knob.

^4 Cue button indicators

• Channels of CUE selected are indicated.

^5 Cue BPM display (Auto count)

• This display indicates the BPM of the selected

channel.

NOTE:

BPM will not be displayed, if 2 or more channels

are selected.

1 2 3 4 5 6 7 8 9 10 11 12 ... 77 78

Komentarze do niniejszej Instrukcji

Brak uwag

Denon DN-X1500S Instrukcja Użytkownika Strona 7

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Miksery audio Denon DN-X1500S